Extraction of Valuable Elements from Industrial Waste in the Kyrgyz Republic Based on the Process of Electrophysical Ionization
1General Department, Osh State University, Kyrgyzstan
2Department of Information Security and Computer Services, Osh State University, Kyrgyzstan
3Department of Experimental and Theoretical Physics, Osh State University, Kyrgyzstan
*Author to whom correspondence should be addressed:
E-mail: abdimitalip.satybaldyev.example@university.edu (AS)
E-mail: abdimitalip.satybaldyev.example@university.edu (AS)
Evergreen, Vol. 12, Iss. 02, pp. 1154–1166, 2025
DOI: 10.5109/7363500
Creative Commons Attribution 4.0 International
DOI: 10.5109/7363500
Creative Commons Attribution 4.0 International
Received: December 10, 2024 | Revised: March 07, 2025 | Accepted: April 19, 2025 | Published: June 2025
Abstract
The relevance of this study is due to the need to find effective and environmentally safe extraction technologies, which is especially important for the Kyrgyz Republic, where industrial waste contains significant amounts of valuable components. The objective of this article is to investigate the applicability and effectiveness of the electrophysical ionization process for extracting valuable elements from industrial waste in the Kyrgyz Republic. The study analyses the mass concentrations of extracted elements after their treatment using electrophysical ionization. The results showed that the electrophysical ionization process is effective for extracting copper with a concentration of more than 1000 ppm, while the concentrations of uranium and tantalum were significantly lower, indicated the need for further optimization of the methodology. Additionally, moderate concentrations of phosphorus, strontium and barium were established which may be promising for their joint extraction. Theoretically, they enrich the knowledge of ionization processes in the context of waste recycling; practically, they pave the way for improving the efficiency of element extraction from waste. The results of the study provide a basis for engineering design, planning and optimization of recycling processes which can contribute to the sustainable development of the regional economy and improvement of the environmental situation.
Keywords
electric field ; spectroscopic analysis ; copper sulphate ; waste recycling ; electrophysical ionisation
Available Repositories
Share Article
Article Metrics
--
Views
--
Downloads
--
Citations
Export Citation
Full Text
References
- 1) H. Sujakhu, W. Jutidamrongphan, "Generation of construction waste in hydroelectric power station in Dolakha District, Nepal," Evergreen, 11 (3) 1613-1624 (2024) doi:10.5109/7236816
- 2) H. Susanto, B. Setio Aji, B.A. Nugroho, R. Mawardi, H.L. Susilawati, T. Cahyono, T. Wahyuni, N.A. Sasongko, T. Martini, "Fuel characteristics of pyrolysis oil from plastic waste: A case study of Banjarnegara Waste Bank," Evergreen, 11(3) (2024), pp. 2404-2414 doi:10.5109/7236883
- 3) T. Martini, M. Anda, N.A. Sasongko, A. Octavian, T. Mumpuni, H. Susanto, M.M.A. Oktaufik, F.M.E. Septiarsi, B.T. Aji, H. Widjanarko, E.K. Purwendah, T. Wahyuni, R. Mawardi, T. Cahyono, H. Hanafi, T. Rahman, A. Meilin, D. Juhandi, "Circular economy for sustainable management of plastic waste to produce liquid fuel and the environmental impact of the whole life cycle (Case study in Banjarnegara, Central Java, Indonesia)," Evergreen, 11 (3) 2447-2457 (2024) doi:10.2139/ssrn.4631180
- 4) A.U. Farahdiba, Y. Franciscus, A. Yuniarto, J. Hermana, "Food waste flows for energy recovery: A material flow analysis approach in urban cities of Indonesia (Study case: Surabaya City)," Evergreen, 11 (3) 2728-2741 (2024) doi:10.5109/7236912
- 5) I. Febijanto, S. Steven, N. Nadirah, H. Bahua, A. Shoiful, D.P. Dewanti, I.P.A. Kristyawan, K.A. Haris, M. Yuliani, M. Hanif, M.H. Robbani, N.R. Yusuf, P. Prihartanto, P. Alfatri, R.A. Pratama, W. Purwanta, R. Wiharja, R. Nugroho, S.K. Ramadhan, "Municipal solid waste (MSW) reduction through incineration for electricity purposes and its environmental performance: A case study in Bantargebang, West Java, Indonesia," Evergreen, 11 (1) 32-45 (2024) doi:10.5109/7172186
- 6) S. Krishnan, N.S. Zulkapli, H. Kamyab, S.M. Taib, M. Din, Z.A. Majid, S. Chaiprapat, I. Kenzo, Y. Ichikawa, M. Nasrullah, S. Chelliapan, and N. Othman, "Current technologies for recovery of metals from industrial wastes: An overview," Environ. Technol. & Innov., 22 101525 (2021) doi:10.1016/j.eti.2021.101525
- 7) J. Abeywickrama, N. Hoth, M. Grimmer, F. Haubrich, and C. Drebenstedt, "Optimizing metal recovery from slag leaching solutions: Advanced ion exchange techniques for sustainable resource extraction," J. Water Process Eng., 56, 104482 (2023) doi:10.1016/j.jwpe.2023.104482
- 8) Y. Zhang, Y. Ji, H. Xu, Y. Yang, and L. Tian, "Life cycle assessment of valuable metal extraction from copper pyrometallurgical solid waste," Resour. Conserv. Recycl., 191, 106875 (2023) doi:10.1016/j.resconrec.2023.106875
- 9) Y, Mubula, M. Yu, D. Yang, B. Lin, Y. Guo, and T. Qiu, "Recovery of valuable elements from solid waste with the aid of external electric field: A review," J. Environ. Chem. Eng., 11 (6), 111237 (2023) doi:10.1016/j.jece.2023.111237
- 10) C.C. Chen, S. Bennetts, and F. Schreck, "Chapter six – The path to continuous Bose-Einstein condensation," Adv. At. Mol. Opt. Phys., 72 361-430 (2023) doi:10.1016/bs.aamop.2023.04.004
- 11) S. Manikandan, D. Inbakandan, C. Valli Nachiyar, and S. Karthick Raja Namasivayam, "Towards sustainable metal recovery from e-waste: A mini review," Sustain. Chem. Environ., 2 100001 (2023) doi:10.1016/j.scenv.2023.100001
- 12) S.S. Siwal, H. Kaur, R. Deng, and Q. Zhang, "A review on electrochemical techniques for metal recovery from waste resources," Curr. Opin. Green Sustain. Chem., 39 100722 (2023) doi:10.1016/j.cogsc.2022.100722
- 13) F. Akhter, S.A. Soomro, M. Siddique, and M. Ahmed, "Pollutant removal efficiency of electrocoagulation method from industrial wastewater: Comparison with Other treatment methods and key operational parameters – A comparative study review," Water Air Soil Pollut., 232 (93) (2021) doi:10.1007/s11270-021-05022-5
- 14) L. Chen, G. Zhang, H. Liu, S. Miao, Q. Chen, H. Lan, and J. Qu, "Efficient metal recovery from industrial wastewater: Potential oscillation and turbulence mode for electrochemical system," Engineering, 38 184-193 (2024) doi:10.1016/j.eng.2023.12.002
- 15) M.H. Anderson, J.R. Ensher, M.R. Matthews, and E.A. Cornell, "Observation of Bose-Einstein condensation in a dilute atomic vapour," Science, 269 (5221) (1995) doi:10.1126/science.269.5221.198
- 16) T. Vibel, M.B. Christensen, R.M.F. Andersen, L.N. Stokholm, K. Pawłowski, K. Rzążewski, M.A. Kristensen, and J.J. Arlt, "Atom number fluctuations in Bose gases – Statistical analysis of parameter estimation," J. Phys. B: At. Mol. Opt. Phys., 57 (19) 195301 (2024) doi:10.1088/1361-6455/ad7458
- 17) N.S. Nzeh, A.P.I. Popoola, A.A. Adeleke, and S.O. Adeosun, "Factors and challenges in the recovery of niobium and tantalum from mineral deposits, recommendations for future development – A review," Mater. Today Proc., 65 (3) 2184-2191 (2022) doi:10.1016/j.matpr.2022.06.034
- 18) S. Gulliani, M. Volpe, A. Messineo, and R. Volpe, "Recovery of metals and valuable chemicals from waste electric and electronic materials: A critical review of existing technologies," RSC Sustainability, 1 1085-1108 (2023) doi:10.1039/D3SU00034F
- 19) N. Totubaeva, Z. Tokpaeva, J. Izakov, and M. Moldobaev, "Bioremediation approaches for oil contaminated soils in extremely high-mountainous conditions," Plant, Soil and Environ., 69 (4) 188-193 (2023) doi:10.17221/433/2022-PSE
- 20) T.I. Turdiev, and A.G. Nizamiev, "Environmental and economic strategy of Kyrgyzstan: Challenges and promising trends," J. Geogr. Nat. Resour., 45 202-208 (2024) doi:10.1134/S1875372824700276
- 21) Y. Tashpolotov, E. Sadykov, T. Ibraimov, and N. Erkinbaeva, "Method of transformation of chemical elements based on the effect of electrophysical ionization," Bulletin Osh State University. Math. Phys. Eng., 1 (1) 146-154 (2021). https://www.elibrary.ru/item.asp?id=46561756 (accessed September 24, 2024)
- 22) S. Raja, M.A. Mustafa, G.K. Ghadir, H.M. Al-Tmimi, Z.K. Alani, M.A. Rusho, and N. Rajeswari, "Unlocking the potential of polymer 3D printed electronics: Challenges and solutions," Appl. Chem. Engin., 7 (2) ACE-3877 (2024) doi:10.59429/ace.v7i2.3877
- 23) A. Shantyr, "Specifics of quality assessment models application at development and use stages of software systems," ІТКІ, 59, 127-138 (2024)
- 24) A. Kulyk, V. Revenok, Y. Kulyk, and O. Nikolskyy, "Development, implementation and use of simulator programs for laboratory work in medical and biological physics," Inf. Technol. Comput. Eng., 59(1), 166-173 (2024) doi:10.31649/1999-9941-2024-59-1-166-173
- 25) N. Temirbaeva, M. Sadykov, Zh. Osmonov, Y. Osmonov, and U. Karasartov, "Renewable energy sources in Kyrgyzstan and energy supply to rural consumers," Machinery & Energetics, 15 (3) 22-32 (2024) doi:10.31548/machinery/3.2024.22
- 26) T. Kravets, M. Semerak, I. Galyanchuk, O. Yurasova, and A. Kharchuk, "Analytical study on improving the efficiency and environmental friendliness of solid organic fuels," Machinery & Energetics, 15 (3) 84-93 (2024) doi:10.31548/machinery/3.2024.84
- 27) R. Subramani, P. Vijayakumar, M.A. Rusho, A. Kumar, K.V. Shankar, and A.K. Thirugnanasambandam, "Selection and Optimization of Carbon-Reinforced Polyether Ether Ketone Process Parameters in 3D Printing—A Rotating Component Application," Polym., 16 (10) 1443 (2024) doi:10.3390/polym16101443
- 28) L.N. Melnikova, "Lean innovation in the textile industry, as a tool for solving problems in the field of waste disposal and recycling," Izvest. Vyssh. Uchebn. Zaved., Ser. Teknol. Tekstil. Promysh., 392 (2) 17-21 (2021)
- 29) A. Sadigov, S. Nuruyev, R. Akbarov, D.B. Berikov, A. Madadzada, A. Mammadli, S. Lyubchyk, and E. Yilmaz, "Compact and sustainable electronic module for silicon photodetectors," Euras. J. Phys. Funct. Mater., 7 (3) 148-154 (2023) doi:10.32523/ejpfm.2023070302
- 30) V.I. Yukalov, and E.P. Yukalova, "Statistical model of a superfluid solid," Physics Letters A, 457 (128559) (2023) doi:10.1016/j.physleta.2022.128559
- 31) A. Panchenko, A. Voloshina, R. Antoshchenkov, I. Halych, and S. Głowacki, "Experimental Studies of the Wear on the Rotors’ Working Surfaces of a Planetary Hydraulic Motor," Lect. Notes Mech. Engin., 1 498-508 (2024) doi:10.1007/978-3-031-42778-7_46
- 32) V. Babak, S. Filonenko, and V. Kalita, "Acoustic emission under temperature tests of materials," Aviat., 9 (4) 24-28 (2005) doi:10.1080/16487788.2005.9635914
- 33) V.P. Babak, S.V. Babak, V.S. Eremenko, Y.V. Kuts, M.V. Myslovych, L.M. Scherbak, and A.O. Zaporozhets, "Models and Measures for Atmospheric Pollution Monitoring," Stud. Syst., Decis. Contr., 360 227-266 (2021) doi:10.1007/978-3-030-70783-5_8
- 34) G.O. Ariunbold, "A cascade superradiance model," Physics Letters A, 452 128468 (2023) doi:10.1016/j.physleta.2022.128468
- 35) R.V. Dinzhos, E.G. Privalko, and V.P. Privalko, "Enthalpy relaxation in the cooling/heating cycles of polyamide 6/ organoclay nanocomposites. I. Nonisothermal crystallization," J. Macromol. Sci – Phys., 44 B (4) 421-430 (2005) doi:10.1081/MB-200061610
- 36) A.E. Akimov, V.V. Boychuk, and V.Y. Tarasenko, "Long-range spinor fields: Physical models," J. Emerg. Direct. Science, 12-13 (4) 121-129 (2016). http://www.unconv-science.org/en/n12/akimov/ (accessed September 25, 2024).E.S. Chernyakova, E.D. Ivanchina, I.V. Yakupova, M.V. Vinidiktova, and G.Z. Seytenova, "Coke formation reduction in the cataltic reforming reactors at the optimal catalyst activity," Petrol. Coal, 58 (7) 746-752 (2016)
- 37) G. Nazarova, E. Ivashkina, E. Ivanchina, T. Shafran, V. Stebeneva, and G. Seytenova, "Testing of cracking zeolite catalysts using mathematical model," AIP Conf. Proceed., 1772 060013 (2016) doi:10.1063/1.4964593
- 38) L. Akhkozov, O. Gorban, I. Danilenko, S. Gorban, G. Volkova, I. Bryukhanova, O. Shapovalova, S. Lyubchik, and T. Konstantinova, "Optical properties, photocatalytic and bactericide activity of pure and Ag-decorated Zr, al-doped ZnO," NANOCON Conf. Proceed. – Int. Conf. Nanomater., 2020-October 186-192 (2020) doi:10.37904/nanocon.2019.8535
- 39) D.D. Nematov, A.S. Burhonzoda, K.T. Kholmurodov, A.I. Lyubchyk, and S.I. Lyubchyk, "A Detailed Comparative Analysis of the Structural Stability and Electron-Phonon Properties of ZrO2: Mechanisms of Water Adsorption on t-ZrO2 (101) and t-YSZ (101) Surfaces," Nanomater., 13 (19) 2657 (2023) doi:10.3390/nano13192657
Other Papers in This Issue
- Natural Frequency and Damping Properties of Composite Sandwich Materials Manufactured using Vacuum-Assisted Resin Infusion, Vacuum Bagging, and Hand Lay-Up
A. Nugroho et al. (2025) - Assessment of Noise Levels in Working with Welding and CNC Milling Machines in Mechanical Workshops of an Academic Institute
A. Kumar, S. Deswal (2025) - Model Predictive and Direct Voltage Control for Standalone DFIG System
P. verma, K. jaladi (2025) - Natural Ventilation Technique: A Bibliometric Analysis of Research Trends
N. Abdul Rahim, P. Szabó, Z. Kovács (2025) - Sorghum Juice from the 'Super 2' Variety: A Promising Carbon Source for Oleaginous Yeast in Biodiesel Production
M. Wattimena et al. (2025) - Development of Optimized Maintenance Scheduling Model for Coal-Fired Power Plant Boiler
N. Fuzi et al. (2025) - Application of CVR in Advanced Distribution Management System using Firefly Optimization
C. Prajapati, S. Chanana (2025) - The Influence of Human Factors and Measurements on the Formation of Cybersickness while using Virtual Reality: Systematic Literature Review
T. Wijayanto, C. Hasibuan, B. Hartono (2025) - Multi-band Series-Fed Millimeter Wave Array Antenna with LP and CP Characteristics for 5G Applications
P. B. G. et al. (2025) - A Sentiment Analysis Study of Banning Single-Use Plastic Bags Based on X Users’ Attitude
Z. Murti et al. (2025) - Comparative Performance Analysis of a PCM-based Solar Dryer under Natural Air Circulation Conditions
R. Jessam et al. (2025) - Investigation of the Thermal and Surface Properties of Glass-Carbon Hybrid Fiber Epoxy Composite
M. Hasin et al. (2025) - Residual Energy and Quality of Service Parameters based Optimization of Congestion-Aware Machine Learning Algorithms
S. HASSIJA, S. Sikka, M. Vijarania (2025) - Forging the Future: Exploring Aluminium AA-6061 Composites through Stir Casting for Advanced Applications and Future Innovations
V. sharma et al. (2025) - Shaping Atmanirbhar Bharat (Self-Reliant India) through Atmanirbhar Nari (Self-Reliant Women): A Roadmap for Empowering Women-Led MSMEs through ICT, Financial Access, and Skill Development
P. Rathi et al. (2025) - Novel Decentralized Solar-DC Systems for Community Energy Self-Sufficiency: A Validated Case Study
R. Oza, K. Mehta, A. Bavarva (2025) - Synthesis of Biodegradable Tissue Paper Comprised of Cellulose Isolated from Rice Straw Waste and Chitosan: Characterizations and The Effect of Chitosan Concentrations
E. KUSRINI et al. (2025) - SMES Supported AGC Performance Evaluation of Multi Machine Multi Area Power Systems
K. Pandey et al. (2025) - Automated Mangrove Detection Method using Combined Machine Learning and Mangrove Index over Indonesia
R. Brahmantara et al. (2025) - A Modal Analysis-Based Cloud-Shaped Flexible Two-Element CPW-Fed Antenna for 5G Wireless Applications
D. John et al. (2025) - Opportunity of Smart Aquaculture and Eco-Farming Integration in POME Bioremediation and Phycoremediation System for Environmental Sustainability
T. Handayani et al. (2025) - Characteristics of Nitrogen and Sulfur Double Doping in Mahogany Wood-Based Porous Carbon for Potential Carbon Capture Application
A. Aprilia et al. (2025) - Machinability Studies on Aluminium-Silicon Carbide-Graphite Hybrid Composites: A Focus on Drilling with HSS Tool
B. Nithyananda et al. (2025) - Simple Hydrothermal Method for One-Dimensional Synthesis of Al-Doped ZnO for an Organic Dye-Based DSSC Application
H. pujiarti et al. (2025) - The Impact of Covid-19 on Small and Medium Enterprises in Bangladesh
H. Uddin, M. Usman (2025) - Evaluating Green Marketing Strategies: Consumer Perceptions and Sustainability in Brand Development
S. Mushtaq, B. Shameem, V. Rana (2025) - A Review on Recent Development and Future Perspective of Nanofluid Utilization in Automotives
S. Gupta, S. Kumari (2025) - Investigating the Impact of Chromium and Titanium in Mechanical and Corrosion Properties of Iron Alloy Coating Materials Deposited via HVOF
R. Sharma et al. (2025) - Automated Steel Surface Defect Detection using Optimized Cascaded CaffeNet Region Network
S. Kesavan et al. (2025) - Optimization of 3D Printing Process Parameters for Improving the Mechanical Behavior of Honeycomb-Core Sandwich Panels
W. Sari, N. Marin (2025) - Phasor Measurement Unit based Fault Detection using Tellegen's Theorem in Geographically Zoned Power Systems
S. Kumar et al. (2025) - Exploring the Behavioral and Psychological Impacts of Smartphone Addiction on Online Gamers: A Quantitative Study
R. Brando et al. (2025) - Gain Enhancement of Star-Shaped Antenna using FSS as Reflector for C-Band Vehicular Communication Systems
C. Sereddy, U. Yalavarthi, T. Boddapati (2025) - Optimizing Frequency Stability in Interconnected Systems with Renewable Energy and EV Integration
N. Kumar et al. (2025) - Measuring Lubricant Concentration in the Mixture with Refrigerant: A Comprehensive Review
I. Sameen et al. (2025) - Industrial Cluster with System Dynamic Approach to Improve Competitiveness: Study on the Micro- and Small-scale Ethanol Industry in Sukoharjo, Indonesia
J. Iskandar et al. (2025) - Transformation of Production Systems in Azerbaijan through Green Economy Principles
A. Alakbarov et al. (2025) - Optimizing Process Parameters in Plastic Injection Molding using the Taguchi Method: A Focus on Minimizing Defects and Improving Product Quality
R. Kumar, K. Bairwa (2025) - Desalination of Groundwater to Preserve Animal Health using a Natural Mineral Sorbent from Western Kazakhstan
S. Satayeva et al. (2025) - Design, Manufacturing, and Experimentation of an Innovative Efficient Energy Harvesting Suspension System
N. Nguyen, D. Do, D. Le (2025) - Modification of Weighted Aggregated Sum Product Assessment Method to Improve Objective Weighting Accuracy in Multi-Criteria Decision Making
M. Mesran et al. (2025) - A New Approach to Weight Allocation in Multi-Objective Optimization on the Basis of Ratio Analysis (MOORA) for Fair Decision Making
D. Desyanti et al. (2025) - Eco-Friendly Pavement Solutions: Geopolymer Concrete with Recycled Aggregates and Geobead Fillers
M. Irnawan, Y. Zaika, A. Munawir (2025) - A Review of Hybrid Nanofluids: Emerging Trends and their Role in Enhancing Parabolic Trough Concentrators Performance
V. Rathore, S. Gupta (2025) - Improved EfficientNetB4 Attention Model for Multi-Disease Detection In Healthcare
D. Kumar, U. Garg, A. Kumar (2025) - Multi-Objective Optimization Approach for Optimizing the Performance of Double-Stage and Lapple Cyclone Separator
A. Aswin et al. (2025) - Sustainable Development and Environmental Journalism: Implementing Societal Progress in Kazakhstan
A. Alimzhanova et al. (2025) - Effect of SiC and B₄C Reinforcements on the Structural and Mechanical Properties of Aluminum Composites Fabricated by Spark Plasma Sintering
S. T et al. (2025) - Mathematical Modeling of Fluidized Bed Drying System: Review and State of the Art
H. Chen et al. (2025) - Extending Legitimacy Theory for Sustainable Business Performance through the Lens of Green Innovation and Financial Synergy
P. Nguyen, B. Khoa (2025) - Thermo-Hydraulic Performance Analysis of a Microchannel Flat-Tube Heat Exchanger with Finned Enhancements
T. Dang, H. Nguyen, K. Thu (2025) - Numerical Simulation of a Multi-Rotor Diffuser Augmented Wind Turbine System by Flux Reconstruction Method
T. Liang, C. Hu, S. Watanabe (2025)
